Tubular Type Recuperative Air Preheater Pre Heating For Thermal Power Plant
Product Details
| Fuel: | Coal | Type: | Pressure Parts |
|---|---|---|---|
| Surface Treatment: | Painted | Range Of Applications: | Power Station |
| Specification: | Customized | HS Code: | 3215960855 |
| Style: | Horizontal And Vertical | Manufacturing Level: | A |
| Highlight |
air preheater for boiler,tubular type air preheater |
||
Product Description
Tubular Type Recuperative Air Preheater Pre Heating For Thermal Power Plant
Introduction
An air preheater (APH) is a general term to describe any device designed to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency of the process. They may be used alone or to replace a recuperative heat system or to replace a steam coil.
In particular, this article describes the combustion air preheaters used in large boilers found in thermal power stations producing electric power from e.g. fossil fuels, biomasses or waste.
Purpose of Preheaters
The purpose of the air preheater is to recover the heat from the boiler flue gas which increases the thermal efficiency of the boiler by reducing the useful heat lost in the flue gas. As a consequence, the flue gases are also conveyed to the flue gas stack (or chimney) at a lower temperature, allowing simplified design of the conveyance system and the flue gas stack. It also allows control over the temperature of gases leaving the stack (to meet emissions regulations, for example).
Specifications
| Name | APH |
| Material | Carbon steel, Alloyor equivalent |
| Structure | Vertical or Horizontal |
| Tubes | Enameled seam or seamless tubes |
| Tube OD | customers required |
| Thickness | 0.34+/-0.06 mm |
| Size | Customized design |
Advantages of Using Air Heater
The recovery of waste heat from the flue gas and heating the air required for Boiler In an air heater gives the following advantages.
a) The Boiler efficiency is increased.
b) More stable combustion in furnace.
c) The combustion is intensified with the use of hot air.
d) Lower grades of coals can be burnt efficiently with hot-air.
e) The use of hot air, improves the heat transfer rate and so less heat transfer area will be required.
f) The combustion is made complete with negligible amount of carbon in ash.
g) Faster load variations are possible.
h) The coal can be dried effectively for easy pulverization and combustion.
Quality Control
1. Fabrication area of 200,000 square meters
2. 150 Engineers
3. 400 Coded welders
4. 60 Licensed Inspectors(NDT Level-III instructors)
5. Class-A Licenses for Design and Manufacture Boiler
6. ISO 9001:2008 Quality System
7. ASME Certificate of Power Boilers
8. ASME 'S','U' and NB stamp authorization
Company Introduction
Established in 1985,Zhangjiagang Hua Dong Boiler Co.,Ltd.(trading as HD Boiler),produces power plant; industrial; waste heat; waste incineration; biomass; organic heat carrier and electric steam boilers. Coupled with a comprehensive range of heating surfaces, HD Boiler brings to the market a unique service including boiler design , fabrication, installation, maintenance and replacement of boiler pressure parts.
Product Highlights
Tubular Type Recuperative Air Preheater Pre Heating For Thermal Power Plant Introduction An air preheater (APH) is a general term to describe any device designed to heat air before another process (for example, combustion in a boiler) with the primary objective of increasing the thermal efficiency ...
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Carbon Steel SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
