Axial Inlet Type Industrial Cyclone Separator For Boiler Power Dust Collection
Product Details
| Condition: | New | HS Code: | 3215960855 |
|---|---|---|---|
| Medium: | Air , Gas , Liquid | Manufacturing Level: | A |
| Pressure: | Low / High Pressure | Port: | Shanghai |
| Highlight |
boiler cyclone separator,dust collector separator |
||
Product Description
Axial Inlet Type Industrial Cyclone Separator For Boiler Power Dust Collection
Product Description
Cyclone separators are commonly used for separating dispersed solid particles from gas phase. These devices have simple construction; are relatively inexpensive to fabricate and operate with moderate pressure losses. Therefore, they are widely used in many engineering processes such as dryers, reactors, advanced coal utilization such as pressurized and circulating fluidized bed combustion and particularly for removal of catalyst from gases in petroleum refinery such as in fluid catalytic cracker (FCC).
| Name | Type |
| Figure (a) | Tangential inlet,axial discharge. |
| Figure (b) | Tanential inlet,peripheral discharge. |
| Figure (c) | Axial inlet,axial discharge. |
| Figure (d) | Axial inlet,peripheral discharge. |
Operation
The driving force for particle separation in a cyclone separator is the strong swirling turbulent flow. The gas and the solid particles enter through a tangential inlet at the upper part of the cyclone. The tangential inlet produces a swirling motion of gas, which pushes the particles to the cyclone wall and then both phases swirl down over the cyclone wall. The solid particles leave the cyclone through a duct at the base of the apex of the inverted cone while the gas swirls upward in the middle of the cone and leaves the cyclone from the vortex finder. The swirling motion provides a centrifugal force to the particles while turbulence disperses the particles in the gas phase which increases the possibility of the particle entrainment.
Characteristics
7. High efficiency over a broad flow range.
8. Flow-optimized design.
9. High safety during operation under pressure.
10. Long-term corrosion protection.
Quality Control
1. Fabrication area of 200,000 square meters
2. 150 Engineers
3. 600 Coded welders
4. 60 Licensed Inspectors(NDT Level-III instructors)
5. Class-A Licenses for Design and Manufacture Boiler
6. ISO 9001:2008 Quality System
7. ASME Certificate of Power Boilers
8. ASME 'S','U' and NB stamp authorization
Company Introduction
Established in 1985,Zhangjiagang Hua Dong Boiler Co.,Ltd.(trading as HD Boiler),produces power plant; industrial; waste heat; waste incineration; biomass; organic heat carrier and electric steam boilers. Coupled with a comprehensive range of heating surfaces, HD Boiler brings to the market a unique service including boiler design , fabrication, installation, maintenance and replacement of boiler pressure parts.
1. Fabrication area of 200,000 square meters
2. 80 Engineers
3. 200 Coded welders
4. 30 Licensed Inspectors(NDT Level-III instructors)
5. Class-A Licenses for Design and Manufacture Boiler
6. ISO 9001:2008 Quality System
7. ASME Certificate of Power Boilers
8. ASME 'S','U' and NB stamp authorization
Product Highlights
Axial Inlet Type Industrial Cyclone Separator For Boiler Power Dust Collection Product Description Cyclone separators are commonly used for separating dispersed solid particles from gas phase. These devices have simple construction; are relatively inexpensive to fabricate and operate with moderate ...
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Carbon Steel SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
