ASME 12Cr1MovG Boiler Superheater Coil for Maintenance
Product Details
| Product Name: | Boiler Superheater | Material: | 12Cr1MovG |
|---|---|---|---|
| Application: | Maintenance And Replacement | Standard: | ASME |
| Tube Bending Technique: | Cold/Hot Bending | Size: | 36mm*6mm |
| Highlight |
ASME Boiler Superheater Coil Hot Bending,Boiler Superheater Coil For Maintenance,stainless steel Boiler Superheater Coil |
||
Product Description
| Attribute | Value |
|---|---|
| Product Name | Boiler Superheater |
| Material | 12Cr1MovG |
| Application | Maintenance and Replacement |
| Standard | ASME |
| Tube Bending Technique | Cold/Hot Bending |
| Size | 36mm*6mm |
The ASME Boiler Superheater made of 12Cr1MovG is designed for reliable maintenance and replacement applications in power plant systems.
In fossil fuel power plants, the superheater section is located in the steam generating furnace. Steam passes through drying equipment in the steam drum before entering the superheater tubes, where it absorbs additional energy from hot flue gases, raising its temperature above the saturation point.
Power plant furnaces may include a reheater section where exhaust steam from the high-pressure turbine passes through heated tubes to gain additional energy before driving intermediate and low-pressure turbines.
Superheater serpentine tube panels are available in two primary installation types:
- Vertical Suspension Type: Single-layer structure typically used in high-temperature superheater and reheater sections. The tube panel connects directly to the header pipe joint and is suspended longitudinally.
- Horizontal Suspension Type: Primarily double-layer structure fixed by water-cooled hanging tubes, commonly used in low-temperature superheater/reheater sections and economizer serpentine tubes.
| Type | Advantages | Disadvantages | Supporting Method |
|---|---|---|---|
| Pendant-type | Firm structural support | Flow blockage by condensed steam; Requires slow restart to purge accumulated water | Supported from above |
| Inverted-type | Proper drainage of condensed steam | Lacks structural rigidity in high speed gas flow | Supported from below |
| Horizontal-type | Proper drainage; Good structural rigidity | Does not view flame directly (mainly convective type) | Supported in vertical gas ducts parallel to main furnace |
With over 30 years of experience, our boiler superheaters and reheaters feature continuous improvements in bending, welding, and design techniques to meet both European and American standards for reliable performance.
Available materials for superheater & reheater fabrication:
- Carbon steel
- Stainless steel
- Nickel and special alloys
Standard tube diameter range: 32-42mm
Product Highlights
ASME Boiler Superheater Coil Of 12Cr1MovG For Maintenance And Replacement Product Specifications Attribute Value Product Name Boiler Superheater Material 12Cr1MovG Application Maintenance and Replacement Standard ASME Tube Bending Technique Cold/Hot Bending Size 36mm*6mm Product Description The ASME ...
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler
High Pressure Power Boiler Heating Surface Membrane Wall Argon Arc Welding For Biomass Boiler Product Introduction Water wall panels with pins usually laid vertically on the inner wall of the furnace wall, it is mainly used to absorb the radiant heat emitted by the flame and high-temperature flue gas in the furnace.It is the main type of evaporating heating surface of all kinds of modern boilers and the basic component of boiler water circulation loop.Because of both cooling
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME
High Frequency Welding H Fin Tube Economizer For Power Plant Boiler ASME Product Description The boiler economizer is a device used to recover waste heat in industrial boilers, usually located at the tail of the flue of the boiler, which increases the feed water temperature and reduces fuel consumption by absorbing the heat of the flue gas, so as to achieve the effect of energy saving and emission reduction. But at the same time, as an environmental protection equipment, the
Carbon Steel SA192 Superheater Coil Argon Arc Welding 100% PT
Product Description: A boiler superheater is an essential component in a boiler system, responsible for increasing the temperature of steam produced by the boiler. One of the key products in this category is the Superheater Coil, designed to enhance the efficiency and performance of boiler systems. This particular superheater is suitable for various fuels, including coal, oil, and biomass, making it versatile and adaptable to different energy sources. The Superheater Coil
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification
Boiler Industrial SA210A1 Steel Boiler Economizer Heat Exchange Part ASME Certification Introduction The H-shaped finned tube is also known as the H-shaped fin tube, also known as the butterfly fin tube. It is to weld symmetrically two pieces of steel with an arc in the middle to form fins (ribs or butterflies), the frontal shape of which resembles the letter "H", so it is called the H-shaped finned tube. The two fins of the H-shaped fin tube are rectangular and approximately
Please use our online inquiry contact form below if you have any questions, our team will get back to you as soon as possible.
